Product Datasheet - Description, Specifications, Materials, Performance, Applications and Features
1. Product Description
A wire mesh filter cap is a compact, self-supporting three-dimensional filter element fabricated from precision woven wire cloth into a domed, bowl, hat, cone or cylindrical cap with vertical or contoured sidewalls. Also known in international trade as a hat-shaped filter, dome strainer, bowl filter or nozzle strainer cap, it is formed through progressive deep drawing, stamping, stretching or die-pressing of woven metal mesh over precision tooling.
In industrial supply, filter caps are classified into two major structural categories based on perimeter edge finishing:
- Rimmed / Edge-Wrapped Filter Caps: The open perimeter is mechanically enclosed by crimping, stamping or roll-wrapping a metal strip over the cut mesh ends. This encloses sharp cut wires completely, prevents wire fraying or particulate shedding into downstream fluid systems, reinforces dimensional stability against radial crushing, and provides a smooth sealing face against bores or mating shoulders.
- Non-Rimmed / Raw-Edge Filter Caps: The drawn cap retains a plain-trimmed, clean-cut, ultrasonically trimmed or spot-welded perimeter without an auxiliary wrapped metal band. Non-rimmed caps offer minimal outer diameter profile, lowest tare weight and maximum open area for press-fitting, insert-moulding into rubber/plastic grommets, or encapsulated installations where tight annular clearance prevents the addition of a rim band.
For rimmed filter caps, edge binding is supplied in three primary rim materials and two distinct rim geometries:
- Rim Material Options: Aluminium (lightweight, easily crimped, cost-effective for general liquid/air service), Stainless Steel AISI 304 / 316 / 316L (maximum mechanical strength, sanitary, corrosion-resistant, high-temperature capable), and Brass / Copper (ductile sealing, non-sparking, excellent fuel, oil and gas compatibility).
- Rim Geometry Types: Vertical Rim (- the wrapped metal band runs axially parallel to the cap sidewall, creating a cylindrical sleeve rim for direct slide-in bore seating without a protruding flange) and Flat Rim / Flanged Rim (- the metal band is pressed radially outward into a flat horizontal collar or brim, acting as a positive locating shoulder and gasket compression face between pipeline fittings, tap seats or valve bodies).
Filter caps serve as critical point-of-use protective barriers directly upstream of high-value components including fuel injection nozzles, gas burners, hydraulic miniature valves, pneumatic actuators, spray nozzles, water dispensers and analytical instrument sampling probes. All weaving, pressing and rim-wrapping operations are performed in our own Anping factory, ensuring unified control over mesh aperture, wall concentricity, rim crimp integrity and cleanliness.
2. Specifications
Filter caps are manufactured according to customer drawings, CAD files or physical samples, as well as in standard metric and fractional-inch bore sizes. The tables below outline structural classifications, rim configurations and available mesh ratings.
| Structure Category |
Edge / Rim Finishing |
Rim Material Options |
Rim Geometry Profile |
Typical Application Duty |
| Rimmed Cap |
Mechanically wrapped metal strip |
Aluminium, Stainless Steel (304/316L), Brass |
Flat Rim (, radial flange) |
Flanged seating between pipeline couplings, tap aerators, valve seat clamping |
| Rimmed Cap |
Mechanically wrapped metal strip |
Aluminium, Stainless Steel (304/316L), Brass |
Vertical Rim ( axial collar) |
Bore insertion, press-fit into tubes/housings without external shoulder clearance |
| Non-Rimmed Cap |
Plain trimmed / clean-cut edge |
N/A (integral mesh edge) |
Formed sidewall, plain rim |
Snap-in bore retainer, miniature nozzle guards, low-clearance in-line seats |
| Non-Rimmed Cap |
Spot-welded / laser-fused rim |
N/A (fused mesh wires) |
Formed sidewall, fused rim |
Anti-fray insert-moulding into plastic/rubber bodies, fuel injector top cups |
2.1 Standard Shapes and Dimensional Ranges
| Cap Shape |
Typical Dimensional Range |
Key Structural Features |
| Dome Cap |
ID 6 - 32 mm, depth 4 - 20 mm; typical e.g. 12.7 mm ID x 16 mm OD x 8 mm deep |
Hemispherical dome providing uniform hydrodynamic flow and large surface area in compact bore |
| Bowl Cap |
Dia 10 - 50 mm, bowl depth 6 - 25 mm, flat or spherical bottom |
Deep bowl cavity maximising contaminant storage capacity ahead of spray/tap orifices |
| Hat / Top-Hat Cap |
Cylindrical body dia 4 - 40 mm, depth 5 - 30 mm, flat top, radial rim |
Stepped profile with vertical cylindrical wall and flat circular flange brim |
| Cone / Funnel Cap |
Base dia 8 - 60 mm, cone angle 30 - 90 deg, point or truncated tip |
Tapered conical screen for inline conical seats, funnel mouths and directional burner nozzles |
| Flat Disc Cap |
Outer dia 1/4", 3/8", 1/2", 3/4" or 6 - 50 mm, shallow wall 2 - 5 mm |
Short vertical cylindrical rim holding a flat mesh face for standard screw-coupling gaskets |
All dimensions are fully customisable to drawing. Tolerances on formed diameters are typically +/-0.10 mm to +/-0.25 mm depending on mesh weight and rim thickness.
2.2 Mesh Specifications and Filtration Ratings
| Mesh count (per inch) |
Typical wire diameter (mm) |
Nominal aperture (micron) |
Typical filtration rating |
| 10 |
0.51 |
2,000 |
2,000 micron |
| 20 |
0.25 |
1,000 |
1,000 micron |
| 40 |
0.18-0.20 |
435-450 |
450 micron |
| 60 |
0.15-0.19 |
230-270 |
230-270 micron |
| 80 |
0.112-0.13 |
190-200 |
190-200 micron |
| 100 |
0.10 |
154 |
150 micron |
| 120 |
0.09 |
120-125 |
120 micron |
| 150 |
0.063 |
106 |
105 micron |
| 200 |
0.05-0.056 |
71-77 |
70-75 micron |
| 300 |
0.032-0.04 |
45-52 |
45-50 micron |
| 363 |
0.03-0.04 |
30-40 |
30-40 micron |
Aperture is calculated from mesh count and wire diameter (aperture = 25.4 / mesh count - wire diameter) and is stated as a nominal value. Standard production mesh counts are 40, 60, 80, 100 and 120; finer counts and Dutch weave specifications are produced to order. The filtration rating to be quoted is always confirmed against the drawing, the fluid and the required cleanliness before the order is placed.
2.3 Construction and Rim Finishing Options
| Construction Item |
Available Options and Trade Specifications |
| Layer Structure |
Single-layer woven cloth; 2-layer or 3-layer composite (fine filtration mesh backed by coarse square mesh or perforated sheet for pressure support). |
| Mesh Weave Types |
Plain weave square mesh (10 - 200 mesh), twill weave square mesh (150 - 400 mesh), plain/twill Dutch weave (down to 20 micron nominal). |
| Perforated / Etched Option |
Micro-perforated sheet or photochemical-etched stainless steel foil formed into caps where rigid uniform round micro-holes are specified. |
| Rim Material Options |
Aluminium strip (annealed 1060/3003), Stainless Steel (AISI 304, 316, 316L), Brass (H62 / H65), Pure Copper, Nickel-plated carbon steel. |
| Rim Geometry Options |
Vertical Rim (sleeve wrap flush with outer wall) vs Flat Rim (90-degree outward horizontal brim). |
| Surface Cleanliness |
Degreased, ultrasonically cleaned in solvent/deionised water, acid-passivated, clean-room packed on request; 100% free of loose metal burrs. |
3. Materials of Construction
| Component |
Material & Grade |
Service Suitability & Environmental Notes |
| Filter Mesh |
Stainless Steel AISI 304 / 304L |
Standard industrial & commercial liquid/gas filtration; drinking water and sanitary applications |
| Filter Mesh |
Stainless Steel AISI 316 / 316L |
Marine, chemical, pharmaceutical, food & beverage; superior pitting resistance against chlorides |
| Filter Mesh |
Stainless Steel AISI 321 / 310S |
High-temperature service up to 600 - 900 degC in engine exhausts, burner caps and flare tips |
| Filter Mesh |
Brass (H62/H65) & Pure Copper |
Fuels, lubricating oils, natural gas, LPG, air-brake circuits; spark-arresting non-ferrous screens |
| Filter Mesh |
Monel 400 / Nickel 200 / Hastelloy |
Seawater handling, hot caustic alkalis, chlorinated solvents, strong non-oxidising acid streams |
| Filter Mesh |
Titanium Gr1 / Gr2 |
High-purity chemical processes, bleaching liquors, medical devices and aerospace fluid lines |
| Rim / Edge Band |
Aluminium (1060 / 3003) |
Lightweight, ductile crimping, economical rim material for fuel, water, air and HVAC caps |
| Rim / Edge Band |
Stainless Steel 304 / 316L |
Heavy-duty mechanical crimp; hygienic, steam-sterilisable, compliant with food and pharmaceutical contact |
| Rim / Edge Band |
Brass / Copper |
Ductile crimp matching brass valve bodies, copper piping joints and spark-resistant systems |
Raw materials are certified to international standards (ASTM, DIN, GB). Mill Test Certificates per EN 10204 Type 3.1 are supplied upon request.
4. Performance and Properties
| Performance Parameter |
Technical Characteristic & Verified Value |
| Filtration Rating |
Approx. 2,000 micron down to approx. 30 micron with woven wire cloth; finer ratings available with multi-layer / Dutch cloth. |
| Operating Temperature |
Stainless steel caps: -200 to +480 degC (continuous); 310S up to 900 degC; brass/copper caps up to 200 degC; aluminium rim up to 250 degC. |
| Corrosion Resistance |
High resistance to oils, organic solvents, industrial water, weak/strong acids and alkalis depending on alloy selected. |
| Mechanical Integrity |
Deep-drawn vertical sidewalls provide strong radial rigidity, maintaining circular cross-section during installation and under differential pressure. |
| Sealing & Anti-Shedding |
Rimmed versions (both flat and vertical) mechanically lock all wire tails inside the metal wrapper, ensuring zero wire liberation into sensitive valves. |
| Reusability & Cleanability |
100% cleanable and reusable; accepts ultrasonic bath cleaning, solvent back-flushing, hot water jetting, air blasting or thermal burn-off. |
| Pressure Differential |
Standard single-layer cap withstands up to 0.2 - 0.5 MPa dP; multi-layer reinforced caps support > 1.5 MPa dP without collapsing. |
5. Applications
| Industry / Field |
Specific Application & Service Duty |
| Automotive & Small Engines |
Fuel injector inlet strainer caps, carburetor screens, oil pump pickup strainers, diesel glow-plug and burner screens. |
| Industrial Water & Plumbing |
Water meter inlet strainers, tap aerator caps, showerhead anti-clogging screens, hose coupling gasket caps, irrigation nozzles. |
| Petrochemical & Chemical |
Sampling valve caps, pilot line filters, analytical instrument intake guards, chemical dosing pump strainer caps. |
| Pneumatics & Hydraulics |
Solenoid valve port screens, pneumatic exhaust muffler mesh caps, pilot hydraulic line miniature protection caps. |
| Spraying & Dispensing |
Agricultural spray nozzle filters, paint spray gun intake caps, adhesive dispensing tips, water misting nozzle strainers. |
| Food, Beverage & Consumer |
Espresso machine group head caps, tea infuser caps, soda fountain dispenser screens, smoking pipe filters, barbecue torch screens. |
6. Key Features
- Complete Structural Coverage: Both Rimmed (包边) and Non-Rimmed (不包边) designs available, matching every bore clearance and mounting mode.
- Versatile Rim Materials: Aluminium, Stainless Steel (304/316L) and Brass/Copper rim bands tailored to media chemistry and cost requirements.
- Precision Rim Geometries: Vertical Rim (竖包边) for smooth axial bore insertion without external shoulder; Flat Rim (平包边) for flanged gasket clamping.
- Zero Media Shedding: Enclosed edge-wrapping binds all cut wire ends, eliminating downstream valve fouling and injector clogging.
- High Form Concentricity: Precision stamping dies ensure consistent diameter and wall height for automated assembly lines.
- Reusable & Cost-Effective: Robust metal construction allows repetitive ultrasonic and backwash cleaning, dramatically lowering life-cycle cost.
- Broad Media Compatibility: Available in 304, 316L, 321, brass, copper, nickel, titanium and Monel alloys.
- Custom Manufacture: Tailor-made to customer drawings, CAD data or samples, with rapid prototype tooling and flexible batch sizes.
7. Ordering Information
To ensure rapid and precise quotation, please specify the following parameters:
- Product type and configuration (see the specification tables in this datasheet).
- Material and grade of the wire cloth, and of any rim, frame, handle or support component.
- Mesh count together with wire diameter, or the required filtration rating in micron, and whether nominal or absolute retention is required.
- Edge treatment: rimmed / edge-wrapped (specify rim profile: vertical or flat; specify rim material: aluminium, stainless steel or brass), non-rimmed (plain trimmed / cut edge), or spot-welded perimeter.
- Layer construction: single layer, 2-layer spot-welded, multi-layer spot-welded, or multi-layer rimmed with perforated backing plate.
- Dimensions: outside diameter, inside diameter, depth, wall / frame thickness, and any shape drawing for irregular / custom-contoured parts.
- Operating conditions: process medium, operating temperature, operating pressure and allowable pressure drop.
- Cleaning method and expected service frequency, plus required certification (e.g. EN 10204 3.1 material certificate).
8. Supplier
Anping County Bolin Metal Wire Mesh Co., Ltd.
Address: NO15, Building 1, B Zone, Wire Mesh World, Anping County, Hengshui City, Hebei Province, China 053600
Tel: 86-0318-5280116 Fax: 86-0318-7020860 Mobile / WhatsApp: +86-170 6528 1888
Website: www.metalmeshfilters.com www.bolinmetalmesh.com
Established 2004 | ISO 9001:2015 | Wire mesh manufacturing for more than 20 years